Displaying Chute & Mounting 42 Inch (2000 Series) parts for the Cub Cadet 19A40003 Twin Rear Bagger

Find a full parts listing for all the parts in the Chute & Mounting 42 Inch (2000 Series) section of your equipment and add them straight to your cart from here.
Search by part description:
1

Cub Cadet 703-07320A-0637 (replaces 703-07320-0637)

Bagger Mounting Plate

Your price: $61.40

0 of these in your cart

Qty:
2

Cub Cadet 703-2489-0637

Cross Brace

Your price: $18.13

0 of these in your cart

Qty:
3

Cub Cadet 703-2490-0637

Catcher Support Bracket

Your price: $46.92

0 of these in your cart

Qty:
4

Cub Cadet 710-3015

Hex Head Screw, 1/4-20 x .75

Your price: $3.58

0 of these in your cart

Qty:
5

Cub Cadet 711-0309A

Clevis Pin, .62" Dia.

Your price: $8.12

0 of these in your cart

Qty:
6

Cub Cadet 911-04069

Grass-catcher Pin, 1/4-20

Your price: $5.68

0 of these in your cart

Qty:
7

Cub Cadet 711-05063

Clevis Pin, 5/16 x .75 Lg.

Your price: $3.28

0 of these in your cart

Qty:
8

Cub Cadet 712-04064

Flange Lock Nut, 1/4-20

Your price: $3.57

0 of these in your cart

Qty:
9

Cub Cadet 714-0117

Internal Cotter Pin, .148 x 3.00

Your price: $3.71

0 of these in your cart

Qty:
10

Cub Cadet 714-04040

Bow-Tie Cotter Pin, 72

Your price: $2.22

0 of these in your cart

Qty:
11

Cub Cadet 723-04008A

Chute Strap, 6.00 Lg.

Your price: $6.51

0 of these in your cart

Qty:
12

Cub Cadet 726-3046

Ratchet Clip

Your price: $3.62

0 of these in your cart

Qty:
13

Cub Cadet 731-04153A

Bagger Discharge Chute, Elbow 38/42" Deck

Your price: $47.70

0 of these in your cart

Qty:
14

Cub Cadet 731-06610

Bagger Chute Adapter

Your price: $25.78

0 of these in your cart

Qty:
15

Cub Cadet 736-0204

Flat Washer, .344 x .62 x .033

Your price: $3.65

0 of these in your cart

Qty:

Cub Cadet 712-3006 (replaces )

Note: Two attachments groups are required to make up a complete bagging system. One Chute & Mounting attachment 19A40005100 (For

Your price: $3.86

0 of these in your cart

Qty:

4-Cycle Equipment

A basic spring service performed each year should include, at least, the following;
Check the Oil and inspect for contaminants such as water (milky), fuel (too full, thin and smells of gas) or metal particles. Contact a service tech if any are found.
Change your oil now and every 25 hours thereafter.
Sharpen blades now and every 25 hours thereafter.
Inspect air filters for dirt accumulation now, and before each usage and clean or replace. Replace air filters after 25 hours.
Inspect spark plugs every 25 hours and replace if fouled.
Grease all bearings and mechanisms requiring grease.
Inspect entire unit including all wear items such as belts, tires, control cables, bearings and other parts and watch for worn, cracked, pinched or otherwise damaged parts, and replace if found.
Drain fuel from fuel system and replace with fresh fuel if it has been over three months since last usage without fuel stabilizer. If performing and end-of-season service, drain fuel tank or run engine until it runs out of fuel. (alternatively you may dose "fresh" fuel with a fuel stabilizer)